Tugas Jarkom
Nama
: M.Bacharudin Jaelani
Nim : 11.240.0350
Kelas : 3P44
Untuk
membuat rangkaian model jaringan seperti
ini :
Dalam tutorial ini kita membutuhkan :
- 5 Router
- 10 PC
- 5 Switch
- kabel straight
- kabel console
- 5 Router
- 10 PC
- 5 Switch
- kabel straight
- kabel console
- serial
DCE dan serial DTE
Langkah – langkah nya sebagai berikut :
1 1) Selanjutnya Atur IP Address 10 PC
dengan ketentuan :
|
Nama PC
|
IP Address
|
Subnet Mask
|
Default Gateway
|
|
PC
1
|
205.7.5.2
|
255.255.255.0
|
205.7.5.1
|
|
PC
2
|
205.7.5.3
|
255.255.255.0
|
205.7.5.1
|
|
PC
3
|
192.5.5.2
|
255.255.255.0
|
192.5.5.1
|
|
PC
4
|
192.5.5.3
|
255.255.255.0
|
192.5.5.1
|
|
PC
5
|
219.17.100.2
|
255.255.255.0
|
219.17.100.1
|
|
PC
6
|
219.17.100.3
|
255.255.255.0
|
219.17.100.1
|
|
PC
7
|
223.8.151.2
|
255.255.255.0
|
223.8.151.1
|
|
PC
8
|
223.8.151.3
|
255.255.255.0
|
223.8.151.1
|
|
PC
9
|
210.93.105.3
|
255.255.255.0
|
210.93.105.1
|
|
PC
10
|
210.93.105.4
|
255.255.255.0
|
210.93.105.1
|
Contoh mengisikan configuration IP pada :
12 )
Setting
dan isikan Konfigurasi Console pada PC :
Konfigurasi
Console PC4
Router>en
Router#conf
term
Enter
configuration commands, one per line.
End with CNTL/Z.
Router(config)#int
fas0/0
Router(config-if)#ip
ad 192.5.5.1 255.255.255.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#int
fas1/0
Router(config-if)#ip
ad 205.7.5.1 255.255.255.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet1/0, changed state to up
Router(config-if)#exit
Router(config)#int
se2/0
Router(config-if)#ip
ad 201.100.11.1 255.255.255.0
Router(config-if)#clock
rate 64000
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial2/0, changed state to up
Router
con0 is now available
Router>en
Router#conf
ter
Enter
configuration commands, one per line.
End with CNTL/Z.
Router(config)#Router
RIP
Router(config-router)#Version
2
Router(config-router)#Network
201.100.11.0
Router(config-router)#Network
192.5.5.0
Router(config-router)#Network
205.7.5.0
Router(config-router)#
Konfigurasi
Console PC 6 :
--- System Configuration Dialog ---
Continue
with configuration dialog? [yes/no]: n
Press
RETURN to get started!
Router>en
Router#conf
term
Enter
configuration commands, one per line. End
with CNTL/Z.
Router(config)#interface
serial2/0
Router(config-if)#ip
add 199.6.13.1 255.255.255.0
Router(config-if)#clock
rate 64000
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#int
se3/0
Router(config-if)#ip
add 201.100.11.2 255.255.255.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#int
fa
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial3/0, changed state to up
Router(config)#int
fa0/0
Router(config-if)#ip
add 219.17.100.1 255.255.255.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial2/0, changed state to up
Press
RETURN to get started.
Router>en
Router#conf
ter
Enter
configuration commands, one per line.
End with CNTL/Z.
Router(config)#Router
RIP
Router(config-router)#Version
2
Router(config-router)#Network
201.100.11.0
Router(config-router)#Network
219.17.100.0
Router(config-router)#Network
199.6.13.0
Router(config-router)#
Konfigurasi
PC 8
Router>en
Router#conf
ter
Enter
configuration commands, one per line.
End with CNTL/Z.
Router(config)#int
se3/0
Router(config-if)#ip
add 199.6.13.2 255.255.255.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial3/0, changed state to up
Router(config)#int
se2/0
Router(config-if)#ip
add 204.204.7.1 255.255.255.0
Router(config-if)#clock
rate 64000
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#int
fa0/0
Router(config-if)#ip
add 223.8.151.1 255.255.255.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial2/0, changed state to up
Router(config)#Router
RIP
Router(config-router)#Version
2
Router(config-router)#Network
199.6.13.0
Router(config-router)#Network
223.8.151.0
Router(config-router)#Network
204.204.7.0
Router(config-router)#
Konfigurasi
Console PC 9
--- System Configuration Dialog ---
Continue
with configuration dialog? [yes/no]: no
Press
RETURN to get started!
Router>en
Router#
config ter
Enter
configuration commands, one per line.
End with CNTL/Z.
Router(config)#int
se3/0
Router(config-if)#ip
add 204.204.7.2 255.255.255.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial3/0, changed state to up
Router(config)#int
fa0/0
Router(config-if)#ip
add 210.93.105.1 255.255.255.0
Router(config-if)#no
shut
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#Router
RIP
Router(config-router)#Version
2
Router(config-router)#Network
204.204.7.0
Router(config-router)#Network
210.93.105.0
Router(config-router)#
Konfigurasi Console
PC 10
--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>en
Router#conf ter
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 210.93.105.2 255.255.255.0
Router(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#
13 )
Untuk
Mengetahui telah terkoneksi dengan lakukan “PING” di command prompt :
Tidak ada komentar:
Posting Komentar